Stainless steel M10 bleed nipple for Brembo single bleed P2 F08 (P8) calipers on pre 1998 models. This is the same length as the genuine Brembo part BRA17659. M10 bleed screw used only on rear of 2003 on models

Part of Guzzi ref. 17659260. Some brake calipers may require a longer bleed screw, we reecommend measuring your existing screw - it should be 15mm from under the flats to the base of the tip.

 5 in stock

A4 marine grade stainless steel M8 bleed screw for Brembo P4 front caliper and Tokico calipers used on post 1997 models

Part of Guzzi ref. 31659281, 31659260, 17659260 and 05659230

 4 in stock

 01659230 GU01659230 01 65 92 30
 0165 9230 0165.9230 01.65.92.30

Brakelight switch

Stop light switch also known as Guzzi ref. AP8224192
See FRA98412 for mounting screw

 3 in stock

03749845-z 03749845 GU03749845 03 74 98 45
 0374 9845 0374.9845 03.74.98.45

The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance. You may find it helpful to fit this valve to the proportioning valve or manifold on your Guzzi. M10 bleed screw used only on rear of 2003 on models

Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping!

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function on this auto bleed valve, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÜV Rheinland.
  See BRA41652 for bleed valve cover

   3 in stock

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Kit containing 2 stainless steel M10 banjo bolts for Brembo brake fittings with copper washers

Supplied with 4 crush washers. Also known as Guzzi ref. 95990033

 2 in stock

95990028-z 95990028 GU95990028 95 99 00 28
 9599 0028 9599.0028 95.99.00.28

Also fits Laverda Jota

Mounting bolt for brake caliper, bolts caliper to fork leg. Supplied in zinc finish.

 2 in stock

AP8152385

Rebuild kit for Brembo Goldline Calipers with 34mm / 30mm pistons. Contains seals, brake grease and instructions in English. One kit required per caliper. Also suitable for some Ducati / Aprilia models.

Caliper seal kit

 2 in stock

The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance.

Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping!

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function on this auto bleed valve, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÜV Rheinland.
  See BRA41652 for bleed valve cover. Fits front calipers only on models listed above.

   2 in stock

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Brembo pad pin kit for Brembo P4 30/34F calipers fitted to front forks, two pins

Brembo ref. 120394230

 1 in stock

 01659130 GU01659130 01 65 91 30
 0165 9130 0165.9130 01.65.91.30